Unmanaged Industrial ethernet switch sdi-541- Industrial networking solution
Home > Products > Westermo > Industrial Ethernet Switches > Unmanaged Industrial Ethernet Switch – SDI-541

Unmanaged Industrial Ethernet Switch – SDI-541

Unmanaged Industrial Ethernet Switch_480px_SDI-541

Unmanaged Industrial Ethernet Switch_480px_SDI-541

 

The Unmanaged Industrial  Ethernet Switch SDI-541 is a simple and cost effective unmanaged switch suitable for use in a wide range of factory and building automation applications. Two models are available – The SC2 for use on up to 2 km (1.24 mi) of multimode fibre and the SC30 for single-mode applications to 30 km (18.6 mi). A high speed switch core ensures full speed on all ports and transparency to any Ethernet protocol.
The Westermo Ethernet Switch SDI-541 is designed for DIN rail mounting into industrial cabinets allowing simple Ethernet connections to be established between PLCs, I/O units, drives, inverters and HMIs. The voltage input of around 24 VDC or AC makes the unit ideal in these types of application and the fault relay can be connected to an I/O unit to provide simple network management.
Designed to work in industrial environments with its IP 31 Aluminium housing and a wide temperature specification the Industrial Ethernet Switch SDI-541 is an ideal automation solution,
The Unmanaged Industrial Ethernet Switch SDI-541 is so easy to use, simply connect power to the screw terminals and plug in your RJ-45 cables. If you plan to use the fault contacts a DIP switch allows configuration whilst LEDs provide simple diagnostics if required.

back to industrial ethernet switch


4-ports 10/100 TX and 1 multi-mode or single-mode Fibre Compact Fast Ethernet Switch
3.2Gbit/s Switch Fabric with excellent data exchange performance
Variable power input, AC 18 – 27 V / DC 18 – 32 V
Fault relay alarm
Aluminum case with IP-31 grade protection
–10 ~ 60ºC operating temperature

• Technology
Standard IEEE 802.3 10 Base-T
IEEE 802.3u 100 Base-TX
IEEE 802.3u 100 Base-FX
IEEE 802.3u flow control
Switch Technology Store and forward technology and with 3.2 Gbit/s switch fabric
Aggregate System Troughput 1.49 Mpps
• Interface
Number of Ports 4 x 10/100 Base-TX with Auto MDI/MDI-X function, Auto-Negotiation1 x 100Base-FX supports multi-mode or single mode Fibre
Connectors 10/100 Base-TX: RJ-45
100Base-FX: Duplex SC
Power/Relay: 4-pin terminal block
Cables RJ-45 connector: supports CAT-3, CAT-4, CAT-5 unshielded twisted pair or shielded twisted pair cable. The link distance is maximum 100 meters.
Fibre: SC, multi-mode or single-mode
Multi-mode Fibre: 50/125 μm or 62.5/125 μm, max. distance 2 kmSingle-mode Fibre: 8/125 μm, 9/125 μm or 10/125 μm, max. distance 30 km
Fibre Transceiver Westermo SDI-541-MM-SC2, multi-mode Fibre
Link Distance: 2 km (Max.), Wave-length: 1310 nm, Min Tx Power: –20 dBm, Max Tx Power: –14 dBm, Min Rx Sensitivity: 0 dBm, Max Rx Sensitivity: –31 dBm, Link budget: 11 dBmWestermo SDI-541-SM-SC30, single-mode Fibre
Link Distance: 30 km (Max.), Wave-length: 1310 nm, Min Tx Power: –15 dBmMax Tx Power: –8 dBm, Min Rx Sensitivity: 0 dBm, Max Rx Sensitivity: –34 dBmLink budget: 19 dBm
Diagnostic LED System: Power (green), Fault (red on)
RJ-45 port: 100 Mbit/s Link (green on) / Activity (green flashing)
10 Mbit/s Link (yellow on) / Activity (yellow flashing)
Fibre port: Link/Activity (green)
Port Alarm DIP Switch  DIP 1 ~ 5: Enable or disable port link down alarm for RJ-45 port 1 ~ 4, Fibre port 5.On: Enable port link down alarm.Off: Disable port link down alarm
• Power Requirements
System Power 2 pins terminal block for DC or AC power input.
DC 18 ~ 32 V with reverse polarity protection.
AC 18 ~ 27 V, 47 ~ 63 Hz
Consumption 4 Watts @ DC 24 V
• Mechanical
Installation DIN-Rail mount
Case Aluminum case with IP-31 protection
Dimension

111.8 mm (H) x 30 mm (W) x 98.2 mm (D) (with DIN rail clip)
111.8 mm (H) x 30 mm (W) x 89 mm (D) (without DIN rail clip)

Weight 377 g with package
295 g without package
• Environmental
Operating Temperature –10 ~ 60ºC
Operating Humidity 0% ~ 95%, (non-condensing)
Storage Temperature –40 ~ 85ºC
Hi-Pot 1.5 KV for all ports and power
• Regulatory Approvals
EMI FCC Class A, CE/EN55022
EMS EN61000-4-2, EN61000-4-3, EN61000-4-4, EN61000-4-5, EN61000-4-6, EN61000-4-8
Safety CE/EN60950
Shock IEC60068-2-27
Vibration IEC60068-2-6
Free Fall IEC60068-2-32

Related Product

be_480px_rfi-10-f4g-t4g
be_480px_DR-260
managed_industrial_ethernet_switch_L106-F2G
fibre converter odw-710-fx
be_480px_MD-21
Managed Industrial Ethernet Switch RFI-18-F16
Water and wastewater | Road | Rail trackside | On board rail | Oil and Gas | Maritime and offshore | Factory automation | Energy | Building automation
Copyright © Gigantika All Rights Reserved.