HYPERLAN-PACK L/M - Industrial Networking Solutions – Industrial Ethernet Switches and Routers
Home > Products > Acksys > HYPERLAN-PACK L/M


High speed wireless Ethernet backhaul



HyperLan-Pack is a solution to establish a high speed Ethernet wireless link between buildings, factories, CCTV cameras, offshore platforms and temporary installations to connect Ethernet networks or Ethernet devices between each other. HyperLan-Pack is available in two versions: long range (up to 5 Km) and medium distance (up to 1.5 Km) at 40 Mbps. Range increase significantly (up to 50 Km) if data rate is reduced to 10 Mbps. The kit is built around two WiFi units and two parabolic antennas, installation is very easy as described below:

 Antenna height calculation depending on distance and land topography
 Antenna mounting on masts
 Antenna tilt calculation using ACKSYS software and a GPS
 Antenna vertical alignment according to calculated tilts using a clinometer
 Antenna horizontal alignment using a compass
 Ethernet cable connexion on each unit
 Radio quality and sustained data rate checking

Installation is now complete, your wireless Ethernet link is established and your network connection is ready to use. HyperLan-Pack relies on the WiFi 5.3 GHz standard (IEEE 802.11a) which is not widely used by WiFi equipments. This offers a good level of protection against perturbations generated by existing WiFi networks; moreover, the RF radiated beam is narrow (few degrees) so it’s almost undetectable.

The radio link between the two units of the Ethernet Air-Pack is secured by the WPA2-PSK authentication and encryption method. Each unit features a 10/100 Base TX auto-sensing, auto MDI/MDIX cross-over RJ45 network interface, maxium TCP data throughput is 40 Mbps. HyperLan-Pack is powered from the Ethernet cable (IEEE 802.3af), it can also be powered from a DC source (+9VDC to +75VDC) for a 7W typical consumption.

  • 10/100 auto-sensing base TX Ethernet port, waterproof M12 8-point Ethernet connector, auto MDI/MDIX cross-over, 25 m RJ45 cable
  • Up to 40 Mbps TCP data rate
  • 5.3 GHz wireless Ethernet link (IEEE 802.11a)
  • Narrow beam (6°) parabolic directional antenna (23 or 28 dBi depending to models), N-type connector
  • Built-in lightning surge protector
  • Pre-configured WPA2-PSK, hidden SSID
  • Administration: SNMP, ACKSYS NDM
  • LEDs signalling for LAN, WLAN network activity and 10/100 mode
  • IP 66 aluminum enclosure (L:80 x l:175 x h:57 mm)
  • Directional antenna diameter: 44 cm (23 dBi), 60 cm (28 dBi)
  • Mast mounting: diameter from 38 to 76 mm
  • Wind loading data: 160 Km/h (200 Km/h with radome), loading: 50 kg (80 Kg with radome)
  • Power from the Ethernet cable POE IEEE 802.3af or from a DC source (+9VDC à +75VDC), 7W typical consumption
  • Operating temperature: -25°C to +70°C (HR 0-99%), storage: -40°C à +80°C
Ethernet throughput (TCP)
10 Mbps
50 Km
20 Mbps
20 Km
40 Mbps
5 Km
10 Mbps
15 Km
20 Mbps
6 Km
40 Mbps
1,5 Km
• References to order
 HyperLan-Pack/M Ready-to-use wireless Ethernet backhaul, high speed, medium range including two radio units, two 23 dBi antennas with lightning surge protection and mast mounting accessories, one 25 meters Ethernet cable per radio unit, POE power supply (not included).
 HyperLan-Pack/L Ready-to-use wireless Ethernet backhaul, high speed, long range including two radio units, two 28 dBi antennas with lightning surge protection and mast mounting accessories, one 25 meters Ethernet cable per radio unit, POE power supply (not included).

Related Product

WLg-xroad-S internal
Water and wastewater | Road | Rail trackside | On board rail | Oil and Gas | Maritime and offshore | Factory automation | Energy | Building automation
Copyright © Gigantika All Rights Reserved.