JetPort 5604i - Industrial Networking Solutions – Industrial Ethernet Switches and Routers
Home > Products > Korenix > JetPort > JetPort 5604i

JetPort 5604i

JetPort 5604i series is a 4-port Isolation Redundant Serial Device Server. Users can use one IP address, Redundant Ethernet paths (RTTD Technology) to control maximum of 4 serial devices over the Ethernet. To configure JetPort Commander, the easy- to- use utility for Windows or choose HTTPS/SSH for secured management. JetPort 5604i series are also equipped with two types of power inputs, four 5V TTL Digital Inputs and two Digital Outputs. JetPort 5604i especially provides 2KV isolation protection for the critical industrial environments. These are value-added feature for user to construct the field installation.

Dimensions

Industrial 4-port Isolation Redundant Serial Device Server

  • 4-ports RS-422/485 with isolation to redundant Ethernet
  • Supports 2KV isolation protection
  • RTTD, Redundant to the Device function Dual Ethernet ports, network auto-recovery in Less Than 200ms
  • Four Digital Inputs and Two Digital Outputs
  • Redundant Power Inputs by 12-48VDC Terminal Block and DC Jack
  • Independent serial services, Virtual COM, TCP Server/Client/Tunnel and UDP Connections
  • JetPort Commander, Easy-to-use Windows Utility with smart setup Wizards.
  • Secured Management by HTTPS and SSH
  • Event Notification by Syslog, Email, SNMP trap and Digital Output
  • Vertical mounting by DIN Rail, Wall mount/Desk-top

Network Interface

Ethernet
2* 10/100BaseTX, Redundant Dual Ethernet
Connector
RJ-45, Auto MDI/MDI-X
Feature
Auto Recovery in less than 200ms
Protection
Built-in 1.5 KV magnetic isolation protection
Protocols
IP, TCP, UDP, ICMP, DHCP, BootP, ARP/RARP, SNMP, HTTPS, SSH, SNTP, SMTP
Serial Communication
Number of Ports
4
Interface
RS422, 2/4-wire RS485
Connectors
5-pin Terminal Block
Serial Port Isolation
2KV
Baud Rates
110 bps to 460.8 Kbps
Data Bits
5, 6, 7, 8
Parity
odd, even, none
Stop Bits
1, 1.5, 2
RS-422
Tx+,Tx-, Rx+, Rx-,GND
RS-485 (4-wire)
Tx+,Tx-, Rx+, Rx-,GND
RS-485 (2-wire)
Data+, Data-,GND
Flow Control
XON/XOFF, RTS/CTS, DTR/DSR
Serial Line Protection
15KV ESD
Long Distance Termination
2*pin 120ohm DIP switches
Isolation
Serial Line Isolation
2KV
Protection Types
Port to Port, Port to Power/GND/Case
Digital Input/Output
Number of DI
4
Power Input voltage
5V/TTL
Logic 0: 0.8V max (0-0.8V)
Logic 1: 2.0V min (2-5V)
Number of DO
2
Power Output voltage
5V/TTL
Logic 0: 0.8V max (0-0.8V)
Logic 1: 2.0V min (2-5V)
Features
LED
Power 1/Power 2: Startup(Red); Ready(Green)
Ethernet port:
Left:100M Link (Green On)/Activity(Green Blinking)
Right:10M Link (Orange On)/Activity(Orange Blinking)
Serial 1/2/3/4:TX only(Green), RX only(Red), Both RX/TX(Orange)
Configuration
Windows Utility-JetPort Commander, HTTP, Telnet
Serial Service
Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP
Reset
Software reload default, Hardware reset button
Beeper
Embedded beeper for positioning
RTTD
Redundant to the Device, Auto-recover in less than 200ms
SNTP
For time management
Access IP Table
16 IP addresses to prevent illegal users
Monitor
Devices¡¦ status, VCOM status
SNMP
RFC1213 MIB II, RFC1317 RS232_like and SNMP Trap
E-Mail Alert
Automatic e-mail warning by pre-defined events
System Log
Trap to Syslog server or local display
System Events
Cold/Warm Start, Login Failed, IP and Password Changed, Access IP Blocked, DI/DO changed, Serial Port DCD/RI/DSR/CTS changed, Serial Port connected/disconnected
Windows Utility
JetPort Commander
Device Discovery, Auto IP, Network Setting, Device and Serial Port Setting and monitoring, Notification setting, Firmware Upgrade, Configuration Backup and Restore, Group Configuration Wizards
Serial Service Mode
Virtual COM, TCP Server, TCP Client, TCP Tunnel and UDP
Advanced Serial Setting
TCP Alive Check Timeout, Inactivity Idle Timeout, Performance mode, Delimiter, Force TX Timeout for Data Packing and Force TX interval time
Group Configuration Wizard
JetPort Commander: Group IP Wizard, Group firmware upgrade, Group Backup/Restore, VCOM and TCP Tunnel Setup Wizard
Power Requirements
System Power
PWR1: 12~48VDC Terminal Block
PWR2: 12~48VDC Power Jack with Power Adapter
Power Line protection
1 KV Burst (EFT), EN61000-4-4
0.5 KV Surge, EN61000-4-5
Mechanical
Dimensions
145mm(W)x46.5mm(H)x120mm(D)
Regulatory Approvals
FCC Class A, CE Class A , UL, RoHS
Environmental
Operating Temperature
-10 to 70°C
Operating Humidity
5% to 95% (Non-condensing)
Storage Temperature
-40 to 85°C
Water and wastewater | Road | Rail trackside | On board rail | Oil and Gas | Maritime and offshore | Factory automation | Energy | Building automation
Copyright © Gigantika All Rights Reserved.