JetI/O 6510 - Industrial Networking Solutions – Industrial Ethernet Switches and Routers
Home > Products > Korenix > JetI/O > JetI/O 6510

JetI/O 6510

 

 

 

 

 

 

 JetI/O 6510 is an intelligent I/O server equipped with one Ethernet port and 8 Analog Input channels. JetI/O 6510 provides 16 bits resolution and high accuracy for I/O data collecting. The analog input range can support from 150mV to 10V and 20mA. The values are most adopted in the industrial environment. JetI/O 6510 provides Windows Utilities, SNMP and Web configuration, industrial Modbus/TCP protocol and OPC Server driver for integrating JetI/O with existing HMI/ SCADA. It also features robust aluminum case with good heat dispersing and IP31 protection. With JetI/O, users can easily perform status monitoring and control of remote I/O devices.

JetIO 6510 Appearance

Dimensions (Unit -mm)

Intelligent 8-CH Analog Input Ethernet I/O Server

  • Ethernet Block I/O with 8 Channel Analog Input from
    150mV to 10V, 20mA
  • 16 bits resolution and high accuracy
  • High/Low Voltage/Current active alarm
  • Intelligent Condition&Go (IF-Then) logic rules
  • Flexible peer-to-peer I/O through one-to-one, one-to-many,
    many-to-one, and many-to-many communication
  • Unicast for network efficiency and true remote I/O
  • Free OPC server and Modbus/TCP support
  • Built-in watchdog timer and real-time clock
  • SNMP / Web for easy configuration and management
  • IP31 grade case protection
  • -25~70oC operating temperature for hazardous
    environmental application
System
CPU
100MHZ, RISC-Based
SDRAM
32K bytes
Flash ROM
512K bytes
EEPROM
256 bytes
Watchdog Timer
1.0 sec H/W
LED
PWR: Power Input plugged and On (Green)RDY: System startup ready (Red)
Network Interface
Ethernet
IEEE 802.3 10Base-T, IEEE 802.3u 100Base-TX
Connector
1* RJ-45, Auto MDI/MDI-X
Protection
Built-in 1.5 KV magnetic isolation protection
LED

Upper (LAN Activity): Orange On & Blinking

Lower(10M/100M): 10M (Green Off) /100M(Green ON)

Analog Input
Channels
8 Differential
Resolution
16 bits
Input Range
Voltage: ±10V,±5V, ±1V, ±500mV, ±150mVCurrent: ±20mA with external 125Ohm resistor
Accuracy
±0.05% of FSR ±1LSB
Sampling Rate
10 samples/sec (total)
Input Impedance
10 M (ohm)
Calibration
On Board EEPROM
Isolation Voltage
2500Vrms
Feature
Network Protocols
IP, TCP, UDP, SNMP, HTTP, BOOTP, DHCP, Modbus/TCP, OPC Server
Configuration
Windows Utility, SNMP, Web, DHCP Client, BootP for firmware update
Flexible peer-to-peer IO
one-to-one, one-to-many,
many-to-one, and many-to-many communication
Windows Utility
Block I/O Utility
OPC Server Utility
OPC Server for Modbus/TCP
SNMP
MIB-II: System, SNMP Trap and Private MIB
SNMP Trap Server
Up to 4 SNMP Trap Server
I/O Rules
High-/Low- Voltage/ Current alarms
Logic Condition&Go Rules
Conditions of the AI values,
Actions include the trap
Power Requirement
System Power
external unregulated +24V (18-32V) 
Power Consumption
Max. 3.2W 
Mechanical
Dimensions
120 (H) x 55 (W) x 75 (D) mm 
Mounting
Din-Rail 
Material
Aluminum
Environmental
Regulatory Approvals
CE, FCC Class A
Operating Temperature
-25 ~ 70°C
Operating Humidity
0 ~ 95% non-condensing
Storage Temperature
-40 ~ 80°C
Water and wastewater | Road | Rail trackside | On board rail | Oil and Gas | Maritime and offshore | Factory automation | Energy | Building automation
Copyright © Gigantika All Rights Reserved.